| This quick installation guide was designed to
help with the basic configuration for the Hunter
ATX. More detailed information can be found in the installation guide.
Processor Installation: When installing the processor, make sure
to select the correct settings through jumpers JP4, JP3 and JP10 as shown
on the tables on the next page.Incorrect voltage selection can cause
damage to the motherboard and void the product warranty.
 To
install the processor follow these steps:
- Lift the lever of the ZIF socket and gently
insert the processor. Make sure the diagonal notch on the processor
matches the notch on the socket. This notch represents pin 1.
- Make sure the processor is inserted all
the way.
- Lower lever.
Memory Configuration: The Hunter ATX features three memory banks
(3 sockets) allowing up to 256MB of DIMM memory. They can be 3.3V unbuffered
SDRAM or EDO modules in sizes of 8, 16, 32, 64 or 128MB.
Processor Configuration Jumper Table
|
Processor
|
CPU Speed
|
BUS Freq.
JP4
|
Multiplier
JP3
|
Vcore
JP10
|
|
Intel® Pentium® Processor (P55C MMX)
|
233 MHz
|
66 MHz
|
3.5 x
|
2.8 V
|
|
200 MHz
|
66 MHz
|
3 x
|
2.8 V
|
|
166 MHz
|
66 MHz
|
2.5 x
|
2.8 V
|
|
Intel® Pentium® Processor (P54C )
|
200 MHz
|
66 MHz
|
3 x
|
3.5 V
|
|
166 MHz
|
66 MHz
|
2.5 x
|
3.5 V
|
|
133 MHz
|
60 MHz
|
2 x
|
3.5 V
|
|
AMD
K6/2 - K6/2E
*please set VCORE and VIO voltages according to CPU marking.
|
400 MHz
|
66 MHz
|
6 x
|
*
|
|
366 MHz
|
66 MHz
|
5.5 x
|
*
|
|
333 MHz
|
66 MHz
|
5 x
|
*
|
|
300 MHz
|
66 MHz
|
4.5 x
|
*
|
|
266 MHz
|
66 MHz
|
4 x
|
*
|
|
233 MHz
|
66 MHz
|
3.5 x
|
*
|
|
200 MHz
|
66 MHz
|
3 x
|
*
|
Processor BUS Frequency Table
| BUS Speed |
50 MHz |
60 MHz |
66 MHz |
| JP4 |
1-2
 |
3-4
 |
5-6
 |
CPU Voltage Table
| JP10 |
1-2 |
3-4 |
5-6 |
7-8 |
| 2.8V |
Off |
Off |
Off |
On |
| 2.9V |
On |
Off |
Off |
On |
| 3.1V |
On |
On |
Off |
On |
| 3.2V |
Off |
Off |
On |
On |
| 3.3V |
Off |
On |
On |
On |
| 3.5V |
On |
On |
On |
On |
| 2.2V |
Off |
On |
Off |
Off |
CPU Multiplier Table
| CPU Rate |
1-2 BFO |
3-4 BFI |
5-6 BF2 |
| 1.5x / 3.5x |
OPEN |
OPEN |
OPEN |
| 2.0x / 6.0x |
CLOSE |
OPEN |
OPEN |
| 2.5x |
CLOSE |
CLOSE |
OPEN |
| 3.0x |
OPEN |
CLOSE |
OPEN |
| 4.0x |
CLOSE |
OPEN |
CLOSE |
| 4.5x |
CLOSE |
CLOSE |
CLOSE |
| 5.0x |
OPEN |
CLOSE |
CLOSE |
| 5.5x |
OPEN |
OPEN |
CLOSE |
CPU Support
- Supports full series of Intel® Pentium®
processors up to 233MHz
- Supports AMDTM K5, K6, K6-2
up to 400MHz.
- On-Board adjustable switching regulator
for single split plane CPUs
Supported Bus Clocks
Memory
- Three banks (3 sockets) DIMM up to 256MB.
Supports 3.3V unbuffered EDO and SDRAM. Memory capacity: 8 to 128MB
High Speed DRAM Cache
- Integrated 256KB pipeline burst SRAM direct-mapped
L2 cache Upgradable to 512KB
On-Board I/O
- Two floppies with 2.88 MB
- Two high speed RS-232 serial ports 16Bytes
FIFO (16550)
- One parallel port (bi-directional, ECP/EPP
compatible)
- One PS/2 mouse connector and one PS/2
keyboard connector
- Two Universal Serial Bus headers
- Dual-channel PCI 32-bit EIDE controller
supports up to PIO mode 4
- ULTRA-DMA up to 33MB/sec. supported
- LS120 drive supported
On-Board Flash Disk (optional)
- On-board single-chip flash disk device
in a standard 32-pin DIP socket
- Up to 144MB of capacity with high-speed
boot-up capabilities
- Flash File System included (FFS)
ROM BIOS
|
