| This quick installation guide was designed
to help with the basic configuration for the Hunter LPX.
More detailed information can be found in the installation guide.
More detailed information can be found in the installation guide.
Processor Installation: When installing the processor, make sure
to select the correct settings through jumpers JP10, JP9, and JP19 as
shown on the tables on the next page. Incorrect voltage selection can
cause damage to the motherboard and void the product warranty.
To install the processor follow these steps:
- Lift the lever of the ZIF socket and gently
insert the processor. Make sure the diagonal notch on the processor
matches the notch on the socket. This notch represents pin 1.
- Make sure the processor is inserted all
the way.
- Lower lever.
Memory Configuration: The Hunter LPX features on-board DIMM and
SIMMs memory capability, but they can not be used at the same time. It
features three memory banks (3 sockets) allowing from 8MB up to 256MB
of FPM, SDRAM or EDO DIMM memory. Also one bank (2 sockets) for SIMMs
modules from 8MB up to 128MB.
Processor Configuration Jumper Table
|
Processor
|
CPU Speed
|
BUS Freq.
JP10
|
Multiplier
JP9
|
Vcore
JP19
|
|
Intel® Pentium® Processor (P55C MMX)
|
233 MHz
|
66 MHz
|
3.5 x
|
2.8 V
|
|
200 MHz
|
66 MHz
|
3 x
|
2.8 V
|
|
166 MHz
|
66 MHz
|
2.5 x
|
2.8 V
|
|
Intel® Pentium® Processor (P54C )
|
200 MHz
|
66 MHz
|
3 x
|
3.5 V
|
|
166 MHz
|
66 MHz
|
2.5 x
|
3.5 V
|
|
133 MHz
|
66 MHz
|
2 x
|
3.5 V
|
|
AMD
K6/2 - K6/2E
*please set VCORE and VIO voltages according to CPU marking.
|
400 MHz
|
66 MHz
|
6 x
|
*
|
|
366 MHz
|
66 MHz
|
5.5 x
|
*
|
|
333 MHz
|
66 MHz
|
5 x
|
*
|
|
300 MHz
|
66 MHz
|
4.5 x
|
*
|
|
266 MHz
|
66 MHz
|
4 x
|
*
|
|
233 MHz
|
66 MHz
|
3.5 x
|
*
|
|
200 MHz
|
66 MHz
|
3 x
|
*
|
Processor BUS Frequency Table
| BUS Speed
|
50 MHz
|
60 MHz
|
66 MHz
|
| JP10 |
| 1 |
 |
6 |
|
| 1 |
|
6 |
|
| 1 |
|
6 |
|
CPU Voltage Table
| JP19 |
1-2 |
3-4 |
5-6 |
7-8 |
| 2.8V |
Off |
Off |
Off |
On |
| 2.9V |
On |
Off |
Off |
On |
| 3.1V |
On |
On |
Off |
On |
| 3.2V |
Off |
Off |
On |
On |
| 3.3V |
Off |
On |
On |
On |
| 3.5V |
On |
On |
On |
On |
| 2.2V |
Off |
On |
Off |
Off |
CPU Multiplier Table
| CPU Rate /
JP9 |
1-2 BFO |
3-4 BFI |
5-6 BF2 |
| 1.5x / 3.5x |
OPEN |
OPEN |
OPEN |
| 2.0x / 6.0x |
CLOSE |
OPEN |
OPEN |
| 2.5x |
CLOSE |
CLOSE |
OPEN |
| 3.0x |
OPEN |
CLOSE |
OPEN |
| 4.0x |
CLOSE |
OPEN |
CLOSE |
| 4.5x |
CLOSE |
CLOSE |
CLOSE |
| 5.0x |
OPEN |
CLOSE |
CLOSE |
| 5.5x |
OPEN |
OPEN |
CLOSE |
CPU Support
- Supports full series of Intel® Pentium®
processors up to 233MHz
- Supports AMDTM K5, K6, K6-2
up to 400MHz.
- On-Board adjustable switching regulator
for single split plane CPUs
Supported Bus Clocks
Memory
- Three banks (3 sockets) DIMM up to 256MB.
- One bank (2 sockets) SIMMs up to 128MB
- Supports FPM, EDO and SDRAM
High Speed DRAM Cache
- Integrated 256KB pipeline burst SRAM direct-mapped
L2 cache upgradable to 512KB
On-Board I/O
- Two floppies with 2.88 MB
- Two high speed RS-232 serial ports 16Bytes
FIFO (16550)
- One parallel port (bi-directional, ECP/EPP
compatible)
- One PS/2 mouse connector and one PS/2 keyboard
connector
- Two Universal Serial Bus headers
- Dual-channel PCI 32-bit EIDE controller
supports up to PIO mode 4
- ULTRA-DMA up to 33MB/sec. supported
- LS120 drive supported
On-Board Flash Disk
- On-board single-chip flash disk device
in a standard 32-pin DIP socket
- Up to 144MB of capacity with high-speed
boot-up capabilities
On-Board Industrial Device
- POST (Power-On-Self-Test) code display
- Hardware / software watchdog Timer
ROM BIOS
|
